HP Q2429A Maintenance Kit for LaserJet 4200 Step by Step Installation Guide (including RM1-0013)
Including individual guide for RM1-0013-000, RM1-0699-000, RM1-0037-000, RM1-0036-000. Clear photo illustration with detailed easy-to-follow steps.
-
-
1Before installing the fuser, turn the printer off and unplug the power cord (wait 30 minutes until the fuser cool down before proceeding).
-
2Remove duplexer from the back of the printer.
-
3Lower the rear output bin cover.
-
4Flex the plastic hinge pin on the bottom left of the rear door and squeeze the left hinge pin to release the holding tab. Slide the rear door to the left to remove from printer.
-
5While grasping onto both sides of the fuser, push the two blue levers on the bottom of the fuser and pull the fuser out.
-
6Install the replacement fuser by inserting it and aligning the left side first, making sure that the fuser is fully seated into the printer and you will hear a sound of both blue levers snap into place.
-
7Reinstall the plastic rear output bin.
-
-
1Open the top cover of the printer and remove the toner cartridge.
-
2Transfer roller is located under the toner cartridge.
-
3Use our special plastic hook (included in the transfer roller box) to pull the left end of transfer roller up and then slide the transfer roller to the left to remove it.
-
4Insert the right side of the new transfer roller first and then the left side, making sure the black plastic clip at the left side of the roller is oriented with the open end facing down and snaps it into position. Note: Do not touch the surface of the transfer roller during installation.
-
-
1Pull the Tray 2 out from the printer.
-
2Lift up to open the hinged plastic guide.
-
3Remove the separation roller by pinching the blue tab on the roller and sliding it off its shaft to the left.
-
4Install the separation roller and make sure the blue tab locks the shaft.
-
-
1Look up into the paper tray cavity in the printer, there are two rollers located in the cavity.
-
2Remove them by pinching the blue tabs on the roller and sliding them off their shafts.
-
3When replacing the feed and pick up rollers, make sure the blue tab locks on the shaft.
-
-
1Remove the cover from the envelope feeder slot by pulling it straight out.
-
2Use your fingers or two flathead screwdrivers to pry outward on both of the tabs at the same time to free the pickup roller.
-
3When you replace new pickup roller, snap the round tabs in first and then the square tabs.
-
4Insert the cover back.
-
-
1Use a flathead screwdriver to pry the gray separation pad up and loose from its black plastic base.
-
2After the separation pad is loose, use your fingers to push the black plastic base down and drag the grey pad out.
-
3When you insert the new replacement separation pad, the grey "teeth" on the pad must point downward and towards you. Then use your fingers to press down firmly on the top of the pad to snap it in place. You will hear a clicking sound as the pad locks in place.
RM1-0013 Fuser Assembly Installation Guide ( part of Q2429A maintenance kit)
Easy to follow installation guide for RM1-0013 fuser, used in Q2429A maintenance kit. Q2429A maintenance kit is specifically designed for HP LaserJet 4200 printers.
RM1-0013 Fuser Assembly Installation Guide ( part of Q2429A maintenance kit)
RM1-0699-000 Transfer Roller Instruction Guide (part of Q2429A maintenance kit)
Easy to follow installation guide for RM1-5462-000 Transfer Roller, used in Q2429A maintenance kit. Q2429A maintenance kit is specifically designed for HP LaserJet 4200 printers.
RM1-0699-000 Transfer Roller Instruction Guide (part of Q2429A maintenance kit)
RM1-0037-000 Feed Separation Roller Installation Guide (part of Q2429A maintenance kit)
Easy to follow installation guide for RM1-0037-000 Feed Separation Roller, used in Q2429A maintenance kit. Q2429A maintenance kit is specifically designed for HP LaserJet 4200 printers.
RM1-0037-000 Feed Separation Roller Installation Guide (part of Q2429A maintenance kit)
RM1-0036-000 Pickup Roller Installation Guide (part of Q2429A maintenance kit)
Easy to follow installation guide for RM1-0036-000 Pickup Roller, used in Q2429A maintenance kit.
RM1-0036-000 Pickup Roller Installation Guide (part of Q2429A maintenance kit)
RL1-0019-000 Pickup Roller Installation Guide (part of Q2429A Maintenance kit)
Easy to follow installation guide for RL1-0019-000 Pickup Roller, used in Q2429A maintenance kit. Q2429A maintenance kit is specifically designed for HP LaserJet 4200 printers.
RL1-0007-000 Separation Pad Installation Guide (part of Q2429A maintenance kit)
Easy to follow installation guide for RL1-0007-000 Separation Pad, used in Q2429A maintenance kit. Q2429A maintenance kit is specifically designed for HP LaserJet 4200 printers.