Printel Refurbished MK-P2015-110 / RM1-4247-MK Maintenance Kit (110V)

HP LaserJet M2727, 2041, P2015 Maintenance Kit MK-P2015-110 Step by Step Installation Guide (including RM1-4247)

MK-P2015-110- HP LaserJet M2727, 2041, P2015 Maintenance Kit Step by Step Installation Guide, Including individual guide for RM1-4247, RL1-1525-000, RL1-0540-000 , RM1-1298-000.  Clear photo illustration with detailed easy-to-follow steps.

    RL1-1525-000 Pickup Roller, Tray 1 Installation Guide

    Easy to follow installation guide for RL1-1525-000 Pickup Roller, Tray 1

    RL1-1525-000 Pickup Roller, Tray 1 Installation Guide

    • 1
      Press the print-cartridge-door button to open the print-cartridge door.
    • 2
      Remove the print cartridge.After removing the print cartridge, only handle it on the ends.
    • 3
      • Grasping the pickup-roller cover with thumb and forefinger, squeeze the left side of the pickup-roller cover to release the left retaining tab, and then slide the cover to the left and up.
      • CAUTIONFailure to slide the cover to the left when removing it can cause the rightretaining tab to break.
    • 4
      Press the two black retaining tabs outward until the pickup roller is released from its seat.
    • 5
      Insert a flatblade screwdriver under the old separation pad and pry up to remove it.
    • 6
      Install the new separation pad. Insert as shown in picture below, then use the flatblade of your7.screwdriver (or your fingers) to firmly press down and lock both sides of the separation pad.
    • 7
      Line up the black retaining tabs in the printer with the grooves in the new pickup roller, and thenpress the pickup roller into the pickup-roller seat until the retaining tabs click.
    • 8
      Grasping the pickup-roller cover with thumb and forefinger, insert the pickup-roller cover's rightretaining tab into the retaining slot.
    • 9
      Squeeze the left side of the pickup-roller cover and insert the left retaining tab in the retainingslot.
    • 10
      Close the print-cartridge door.

    RL1-0540-000 Pickup Roller, Tray 2 Installation Guide

    Easy to follow installation guide for RL1-0540-000 Pickup Roller, Tray 2

    RL1-0540-000 Pickup Roller, Tray 2 Installation Guide

    • 1
      Remove tray 2.
    • 2
      Open the automatic two-sided path door on the front of the printer (HP LaserJet P2015d,HP LaserJet P2015dn, and HP LaserJet P2015x printers only).
    • 3
      Place the printer on the work surface with the front of the printer facing up.
    • 4
      Pull the white tabs outward, and rotate the tabs up.
    • 5
      Slide the right tab to the right, and leave the tab in this position throughout the procedure.
    • 6
      Slide the pickup roller assembly to the right, and remove the left end cap.
    • 7
      • Remove the old pickup roller.
      • Save both idler rollers that sit on either side of the pickup roller; transfer to new roller.
    • 8
      Insert the left side of the new pickup roller into the left slot (1), and insert the right side (the sidethat has the notches in the shaft) into the right slot (2).
    • 9
      Place the end cap over the shaft on the left side, push the end cap to the right, and rotate thetab downward into position.
    • 10
      Rotate the shaft until the notches engage and the shaft clicks into place.
    • 11
      Push the right tab to the left, and rotate the tab downward into position.

    RM1-1298-000 Separation Pad Assy, Tray 2 Installation Guide

    Easy to follow installation guide for RM1-1298-000 Separation Pad Assy, Tray 2

    RM1-1298-000 Separation Pad Assy, Tray 2 Installation Guide

    • 1
      Remove the cassette paper tray (tray 2) from the printer.
    • 2
      Remove the 2 screws (circled in picture below) which secure the separation pad.
    • 3
      Remove the old separation pad assembly. Insert the new assembly and replace the screws.

    RM1-4247-000 Fuser Assembly (110V) Cover Installation Guide

    Easy to follow installation guide for HPM 2727 HPP 2015 RM1-4247-000 Fuser Assembly (110V). This instruction is about the Covers:

    • Left-side cover
    • Right-side cover
    • Back cover
    • Duplexer tray
    • Top cover

    RM1-4247-000 Fuser Assembly (110V) Cover Installation Guide

    • 1
      • Left-side cover
      • Open the print-cartridge door.
      • At the back of the printer, use a flat-blade screwdriver to release two tabs (1).
      • Lift the cover away from the printer.
    • 2
      • Right Side Cover
      • Open the print-cartridge door.
      • Remove tray 2.
      • At the front of the printer, pop the front edge of the right-side cover over the two retaining tabs.
      • Lift the cover away from the printer.
    • 3
      • Back cover
      • Remove tray 2.
      • Remove the left-side cover and the right-side cover.
      • Remove four screws (1).
      • Tip the printer so that it rests on its front.
      • Release the tab (2) at the back of the printer on the right side.
      • Open the duplex access door (3).
      • Slide the cover toward the right side of the printer to clear the tab (1) on the duplexer tray(duplex models only).
      • Lift the cover straight up and away from the printer.

    RM1-4247-000 Fuser Assembly (110V) Fan, Duplex-drive gears, Duplex solenoid Installation Guide

    Easy to follow installation guide for HPM 2727 HPP 2015 RM1-4247-000 Fuser Assembly (110V). Several parts must be removed before you can remove the fuser. The following parts are included in this section about removing the fuser: Fan, Duplex-drive gears/face-down gears and Duplex solenoid.

    RM1-4247-000 Fuser Assembly (110V) Fan, Duplex-drive gears, Duplex solenoid Installation Guide

    • 1
      • Fan
      • Remove all covers.
      • Disconnect the fan cable (1) at the ECU.
      • Unthread the fan wires from the retaining clips.
      • Remove two screws (1).
      • Unhook the fan clip (2) and then lift the fan off the printer.
    • 2
      • Duplex-drive gears (HP LaserJet P2015d, P2015dn, and P2015xprinters only)
      • Remove all covers.
      • Remove the fan.
      • Remove three screws (1).
      • Lift the assembly away from the printer. The gears are not attached to the gear plate. Carefully remove the gear plateand the gears together to prevent them from falling out of the assembly.
    • 3
      • Duplex solenoid (HP LaserJet P2015d, P2015dn, and P2015xprinters only)
      • Remove all covers.
      • Remove the fan.
      • Remove the duplex-drive gears.
      • Disconnect one cable (1) at the duplex-drive PCA.
      • Remove one screw (2), and then lift the solenoid off the printer chassis.

    RM1-4247-000 Fuser Assembly (110V) Installation Guide

    Easy to follow installation guide for HPM 2727 HPP 2015 RM1-4247-000 Fuser Assembly (110V). Several parts must be removed before you can remove the fuser. The following parts are included in this section about removing the fuser:

    • Fan
    • Duplex-drive gears/face-down gears
    • Duplex solenoid
    • Fuser

    This instruction is about removing the fuser. 

    RM1-4247-000 Fuser Assembly (110V) Installation Guide

    • 1
      Remove all covers.
    • 2
      Remove the fan.
    • 3
      Remove the duplex-drive gears or face-down gears.
    • 4
      Remove the formatter.
    • 5
      On the right side of the printer, press the tabs on two gears (1) to release the gears, and thenslide the gears off the shafts.
    • 6
      Disconnect one cable (2) on the right side of the printer.
    • 7
      Disconnect four cables (1) from the ECU, and then disconnect two more cables (2) that werebehind the first set.
    • 8
      Pull the tab on the cable holder (1) at the left side of the printer and slide it toward the center torelease it from the frame, and then unroute the cables.
    • 9
      Pull the tab on the cable holder (2) and slide it toward the center to release it from the frame,and then unroute the cables.
    • 10
      Remove one screw (1) from the fuser cover, and then slide the fuser cover to the right andremove it.
    • 11
      Disconnect three cables (1).
    • 12
      • Disconnect one cable (1), and then unroute the cable from the cable guide.
      • Before you proceed to step 13, make sure that all cables disconnected inprevious steps are free from any cable guides and cable holders.
    • 13
      Remove three screws (1) on the right side of the printer.
    • 14
      Remove three screws (1) from the left side of the printer.
    • 15
      At the left side of the printer, pull the printer chassis from the top to spread the printer frame andrelease the fuser from the frame.
    • 16
      Pull the fuser out of the printer at an angle so that the delivery roller shaft clears the hole (1) inthe chassis.